Tedbîrên ji bo sazkirin û ceribandina makîneya makîneya teqîna gulebarana çengelê

Ewhook type teqîna teqîna makîneyabi gelemperî xuyangek mezin heye, û pêvajoya sazkirinê ji ya alavên piçûk nisbeten tevlihevtir e. Sazkirina rast û makîneya ceribandinê mifteya misogerkirina xebata normal alavên paşê ne. Di doza karûbarên destpêkê yên nehsandî de, ji bikarhêneran tê xwestin ku bi hişkî rêwerzên personelên têkildar bişopînin an jî rêwerzan bişînin. Operasyona bê destûr bi hêsanî dikare zirarê neguhêzbar bidehook teqîna makîneya teqandinê. Ewshot blasting machine manufacturer has sorted out the precautions for installation and test machine to share with you. I hope it will be helpful to users who use the device for the first time.
1. Installation. Ewhook type teqîna teqîna makîneya is installed and debugged in the production plant and disassembled into several parts before being transported to the user site for installation. Although there is no pit, the foundation must be firm, the anchor bolt holes must be standardized, and the chamber body must be adjusted. After the second irrigation, the anchor bolt nuts can be tightened after solidification. After the chamber body is fixed, the various parts can be installed. Ewprecautions for the installation and debugging of the relevant components are introduced below.
1. Amûra teqandina teqînê:
Ewshot blasting device has been installed on the chamber body before leaving the factory. Please pay attention to the problems to be debugged before use. Check whether the fixed positions of the blade, the pill wheel, the directional sleeve, and the guard plate are accurate and firm, and check whether the direction of rotation is correct after power on. Then adjust the position of the directional sleeve opening. Theoretically, the angle between the front edge of the directional opening and the front edge of the blade throwing position is about 900. After fixing the position of the directional sleeve, the position of the projectile belt can be detected by hanging Place a steel plate or wooden board on the position of the workpiece facing the exit of the shot blasting machine, start the shot blasting machine, put a small amount (2-5kg) of projectiles into the blasting tube, and then stop, check whether the hit position on the steel plate is suitable for the needs, such as Close the window of the bias-adjustable directional sleeve downwards, and vice versa, until it fits, and note the position of the directional sleeve opening as a basis for future replacement of the directional sleeve.
2. Veguhestin û hilkêşanê:
Pêşîn ceribandinek bê-barkirinê bikin da ku hûn binihêrin ka kewê hilkêşanê û kelûpelên spiral di rêça rast de dimeşin an na, dûv re kemberê hilkêşê heya astek nerm a tengezariyê teng bikin da ku ji devjêberdanê dûr bikevin, û dûv re ceribandinek barkirinê bikin da ku kontrol bikin karîgerî û veguheztina kapasîteyê, gelo xerîbiyek heye Deng û lerizîn, astengiyan derxînin û derxînin.
3. Veqetandek pîl-sand:
Pêşîn kontrol bikin ka tevgera bezê zexm e, û dûv re cîhê rastê yê plakaya veqetandî kontrol bikin, dûv re gava ku hilkêşbar tê barkirin û xelet kirin, herikîna domdar a fîşekên pola heye, û kontrol bikin ka guleyên pola diherikin û dikevin dema ku çît tê berdan